========================================================================================= Latest information ========================================================================================= The most recent versions of the firmware for this unit as follows Unit firmware : V2.14 (Previously V2.13. Updated at this time) FPGA firmware : V0019 (Previously V0013. Updated at this time) Drive firmware : T.4A/T.0J (Not Updated at this time) [ NOTE ] First update the Unit firmware to V2.14, then update the FPGA firmware to V0019. If the Unit firmware is V2.13 or earlier, the FPGA firmware cannot be updated to V0019. Always use the most recent firmware version for this unit. For information about the latest firmware, visit the TASCAM Web Site ( https://tascam.jp/int/product/ss-cdr250n/support ). ========================================================================================= Precautions for updating - Be careful not to let the power be interrupted during the update. - Do not load or remove media during the update. - If the power is interrupted or media is loaded or removed during the update, the unit might become unstartable. ========================================================================================= Unit firmware: V2.14 FPGA firmware: V0019 (December, 17 2024) ----------------------------------------------------------------------------------------- < Maintenance items > - When the media was set to CD and the PLAY MODE to SINGLE, selecting and playing another track some time after stopping playback of the first track could cause the sound to break up on rare occasions. This has been fixed. - When the FILE TYPE in the recording settings was set to MP3 (MONO (2ch)), "Record Error!" would be displayed immediately after recording started, and recording would no longer be possible. This has been fixed. - When playing back a file that was only about one second long, the audio at the end of the file could be repeated. This has been fixed. - When playing back files in succession, if the first song was longer than the second song and the second song was less than 10 seconds long, the second song would be played twice in succession. This has been fixed. - Operation stability has been improved. [ NOTE ] First update the Unit firmware to V2.14, then update the FPGA firmware to V0019. If the Unit firmware is V2.13 or earlier, the FPGA firmware cannot be updated to V0019. ----------------------------------------------------------------------------------------- Unit firmware: V2.13 (November, 2024) ----------------------------------------------------------------------------------------- < Maintenance items > - The IC change for units with serial numbers (24X0001 and later) is now supported. No changes have been made to the functions or specifications resulting from it. ----------------------------------------------------------------------------------------- Unit firmware: V2.12 (August, 15 2023) ----------------------------------------------------------------------------------------- < New functions > - Chinese fonts that comply with the GB18030-2022 standard are now supported. < Maintenance items > - If the pitch control function was on and the playback mode was set to "CONTINUE", a silent gap would occur between files when files were played back continuously. This has been fixed. - If backup recording was conducted to media with a capacity of 64 GB or more, files that could not be recognized as audio data would sometimes be created. This has been fixed. - When the automatic track function was set to "TIME", recording files of 2 GB or more, which cannot be recognized by this unit, could be created. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V2.11 (May, 15 2023) ----------------------------------------------------------------------------------------- < Maintenance items > - If the pitch control function was turned on and the pitch was changed when a file was played back, a few milliseconds of sound at the end would be missing. This has been fixed. ----------------------------------------------------------------------------------------- Unit firmware: V2.10 ----------------------------------------------------------------------------------------- < New functions > - "CURRENT MEDIA RECORDABLE TIME SENSE", which acquires the recordable time of the current media, has been added to the RS-232C/TELNET commands. See the RS-232C/TELNET protocol Ver1.15 specifications for details. < Maintenance items > - When the playback area was FOLDER, executing a RS-232C/TELNET command "DELETE(0x7F03)" would sometimes delete a file other than the intended one. This has been fixed. - Files created with the recording file format set to MONO (MIX) would be shown as "STEREO" when their INFO was viewed from the BROWSE menu. This has been fixed. - When the playback mode was not CONTINUE and the FTP CLIENT AUTO UPLOAD setting was DEL. AFTER UPLOAD, the "Deleting Uploading File..." pop up that appeared after recording would freeze. This has been fixed. Operation has been changed so that when the AUTO UPLOAD setting is DEL. AFTER UPLOAD, the playback mode is automatically switched to CONTINUE when recording starts. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V2.01 ----------------------------------------------------------------------------------------- < Maintenance items > - As result of changes to the audio IC, DAT is not supported with the DD operation mode of the automatic track function by products with serial numbers of 2140001 and higher. (Products with serial numbers lower than 2140001 will continue to support DAT even if their firmware is updated.) ----------------------------------------------------------------------------------------- Unit firmware: V2.00 ----------------------------------------------------------------------------------------- < New functions > - A function has been added that enables marks to be recorded especially for minute-taking applications when used in combination with an Audio-Technica Corporation ATDM-1012 or ATDM-1012DAN Digital SmartMixer. See the operation manual (D01306120C) or addendum (D01369600A) for details. ----------------------------------------------------------------------------------------- Unit firmware: V1.43 ----------------------------------------------------------------------------------------- < New functions > - USER04 and USER05 options have been added to [MENU]-[REC4]-[FILE NAME]. When FILE NAME is set to USER04 or USER05, strings of up to 12 characters set by the user can automatically be added as file names during recording. USER WORD PRESET, USER WORD SENSE and FILE NAME SELECT using RS-232C/TELNET are also now supported in the same manner. - SPECIFIED DEVICE STATUS SENSE and MEDIA FORMAT using RS-232C/TELNET are now supported. See the RS-232C/TELNET protocol Ver1.14 specifications for details. < Maintenance items > - If the auto ready function was turned off immediately before the playing track completed, the unit would skip ahead two tracks and play it. This has been fixed. - A POWER CONTROL command using RS-232C/TELNET would sometimes return 0xF4. This has been fixed to return 0xF5. - If either IP SETUP or DNS SETUP setting mode was set to STATIC, the DNS ADDRESS would be fixed to "0.0.0.0". This has been fixed. If STATIC is selected in IP SETUP, even if DNS ADDRESS is set to AUTO, it will become the value set for STATIC. ----------------------------------------------------------------------------------------- Unit firmware: V1.42 ----------------------------------------------------------------------------------------- < New functions > - Support was added for USER WORD PRESET and FILE NAME SELECT using RS-232C/TELNET. See the RS-232C/TELNET protocol Ver1.13 specifications for details. < Maintenance items > - RS-232C PARITY BIT setting ODD and EVEN behaviors were reversed. This has been fixed. - If the TIMER EVENT function was ON, executing PLAYLIST RENAME and DELETE operations would cause timer events not to be executed. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.41 ----------------------------------------------------------------------------------------- < Maintenance items > - When a medium different from the current one was selected, the TASCAM SS250 CONTROL (Ver2.0.0) would be forced to quit. This has been fixed. - When using the link playback function, sometimes the slave device would not follow the master device. This has been fixed. - When the resume playback function was set to OFF, after selecting a track using the TASCAM SS250 CONTROL, pressing the PAUSE button would not pause and pressing the PLAY button would incorrectly cause playback to start from the first track. These problems have been fixed. - If the auto ready function was turned on immediately before the playback track completed, the unit would not pause at the beginning of the next track. This has been fixed. - When the auto cue function was set to ON and the unit was paused, selecting another track on the BROWSE screen and executing the SELECT operation from the pop-up menu would cause playback to start with the PLAY LED blinking. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.40 ----------------------------------------------------------------------------------------- < Maintenance items > - When the play area was "FOLDER", if playback was started from an external remote control while the current folder name pop-up was being shown when changing folders, a "PLAY ERROR" could occur. This has been fixed. ----------------------------------------------------------------------------------------- Unit firmware: V1.39 ----------------------------------------------------------------------------------------- < Maintenance items > - If backup recording was repeated when the recording file format setting was MONO(MIX) or MONO(2ch), the names of the created files would not always be numbered consecutively. This has been fixed. ----------------------------------------------------------------------------------------- Unit firmware: V1.38 ----------------------------------------------------------------------------------------- < Maintenance items > - When the remote power control function was set to on and the unit was in standby, connecting from an external FTP client could cause control to become no longer possible. This has been fixed. - If the sampling frequency of the first file played after turning the power on was not 44.1 kHz, sound output would be late. This has been fixed. ----------------------------------------------------------------------------------------- Unit firmware: V1.37 ----------------------------------------------------------------------------------------- < New functions > - "OFF" has been added to the POWER ON ACTION functions. OFF: When power is turned on by an external source, the unit enters standby. PLAY: When power is turned on by an external source, the unit automatically starts playback. REC: When power is turned on by an external source, the unit automatically starts recording. STOP: When power is turned on by an external source, the unit resumes a stopped state. < Maintenance items > - When the unit was in standby after being turned on by an external source, operation with an external controller was not possible even when the REMOTE POWER CONTROL function was ON. This has been fixed. - When using the BROWSE function to view WAV file information, an incorrect date would be shown. This has been fixed. - If the power was turned on and off repeatedly, playback would not resume in some cases even though the RESUME function was on. This has been fixed. ----------------------------------------------------------------------------------------- Unit firmware: V1.36 ----------------------------------------------------------------------------------------- < Maintenance items > - Incrementing the track after recording in MP3 format for a long time would cause recording to stop and a "Media Full" pop-up message to appear even if sufficient open space was available. This has been fixed. - When using the link playback function, sometimes the slave device would not follow the master device. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.35 ----------------------------------------------------------------------------------------- < New functions > - A REBUILD function has been added that rebuilds the management data of files and folders. Use MENU > MEDIA > MEDIA REBUILD to execute this function. < Maintenance items > - If media was loaded into the unit after a folder had been deleted using a computer, sometimes existing tracks could not be played back in folder playback mode. This has been fixed. - A "PLAY ERROR" would occur when playing from a USB flash drive. This has been fixed. - If the BROWSE operation was used to change the current folder when the playback area was folder, the resume playback position would not be cleared. This has been fixed. - If the EDIT, PITCH, KEY or INPUT button was pressed when the COMBINE editing execution waiting screen was open, repeat playback would continue. This has been fixed. - If recording was executed and stopped when the auto upload function was on and the playback area was set to folder, the number of playback tracks would be the number on the entire media rather than the number inside the folder. This has been fixed. ----------------------------------------------------------------------------------------- Unit firmware: V1.34 ----------------------------------------------------------------------------------------- < Maintenance items > - If the unit was turned on when the auto ready and resume playback functions were on and the power on action function was set to PLAY, a "READING MEDIA" pop-up would appear while still in playback standby. This has been fixed. - When a download event was executed as a timer event function, the upload icon would be shown in addition to the download icon. This has been fixed. - If the RS-232C "CURRENT TRACK TIME RETURN"(0xD8) exceeded 10000 minutes, "--------" was returned. This has been changed so that if 100 hours is exceeded, "5999 minutes 59 seconds 99 frames" will be returned. - The sound quality when recording a low-level input signal in MP3 format has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.33 ----------------------------------------------------------------------------------------- < Maintenance items > - Editing of file and folder names could not be done properly using RS-232C/TELNET. This has been fixed. - After locking panel operation on the unit, the panel lock status could not be acquired properly using RS-232C/TELNET after restarting the unit. ----------------------------------------------------------------------------------------- Unit firmware: V1.32 ----------------------------------------------------------------------------------------- < New functions > - The output status of the PARALLEL connector 11-pin (Record Tally) when recording is paused can now be set. Set using the [MENU]-[REMOTE]-[RECORD TALLY] item. REC ONLY: Record Tally is not output when record?ing is paused. REC PAUSE/REC: Record Tally is output when recording is paused. (Low state) < Maintenance items > - When the resume playback function was turned off, random playback was not possible sometimes. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.31 ----------------------------------------------------------------------------------------- < Maintenance items > - During synchronized recording, recording would be late after the sync level was detected. This has been fixed. - When using the timer event function, sometimes events would not be executed at their set times. This has been fixed. - When using flash start, the audio output was delayed compared to other media if the medium was CD. This has been fixed. - After setting DYNAMICS to "COMP SOFT" or "COMP HARD" and restarting the unit, the setting would not be retained. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.30 ----------------------------------------------------------------------------------------- < New functions > - TASCAM SS250 CONTROL (Ver2.0.0) is now supported. - Support has been added for POWER CONTROL commands and TIME SKIP setting value change commands using RS-232C/TELNET. POWER CONTROL commands are enabled by setting MENU > UTILITY > REMOTE POWER CONTROL to ON. See the RS-232C/TELNET protocol specifications Ver1.11 for details. [ Confirm the following items before using a TASCAM SS250 CONTROL ] To use TASCAM SS250 CONTROL, confirm that its application version is Ver2.0.0 or higher. If the version is older than Ver2.0.0, install Ver2.0.0 or higher. For information about how to install the application, visit the TASCAM Web site ( https://tascam.jp/int/product/ss250_control/support ). < Maintenance items > - External synchronization was not possible even if OUTPUT RATE was set to EXTERNAL. This has been fixed. - TIMER EVENT LIST "REC" events would operate with BALANCED input even if COAX/AES/Dante was selected by INPUT SELECT. This has been fixed. - Did not respond to READY (0x14) commands by RS-232C/TELNET. This has been fixed. - When copying files to an FTP server during recording by AutoUpload or BROWSE, 2GB files could not be transferred. This has been fixed. - If recording for long periods of time was repeated when AutoUpload was set to ON, the beginnings of the audio files created were missing. This has been fixed. - Searching forward/backward and moving between folder levels with the BROWSE screen open was not possible using the TASCAM RC-10 wireless remote control. This has been fixed. - During digital output of CD-DA playback, time information was not output correctly. This has been fixed. - After setting an event list, if the clock on the unit was turned back through the date and time setting, for example, some events would not be executed. This has been fixed. - When using an RC-SS20, pressing the RC-SS20 LOAD/STOP button would not stop playback of tracks 11-20. This has been fixed. - If different files were added for-playback events, playback of the 11th and later files was not possible. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Drive firmware: T.0J ----------------------------------------------------------------------------------------- < Maintenance items > - Operation stability has been improved. [ NOTE ] If the drive firmware is version T.0H, update the firmware to V1.20 before updating the drive firmware to T.0J. ----------------------------------------------------------------------------------------- Unit firmware: V1.20 ----------------------------------------------------------------------------------------- < New functions > - Support has been added for file RENAME and folder operation and editing commands using RS-232C/TELNET. See the RS-232C/TELNET protocol specifications Ver1.10 for details. < Maintenance items > - DIVIDE scrub playback would not stop when using an external controller. This has been fixed. - If an entry was deleted during playback in PLAYLIST mode, a different track than the track assigned to the entry would be played back. This has been fixed. - During relay recording, after switching to the SUB media for recording, pausing recording would cause the remaining time display to show "0:00". This has been fixed. - After recording with INPUT SELECT set to DIGITAL, if recording was conducted with AUTO TRACK set to DD and DIRECT REC set to ON, recording could not be stopped. This has been fixed. - CUE points could not be detected during AUTO CUE playback of tracks recorded as MONO (MIX). This has been fixed. - When the "***_02.***" file of a track recorded as MONO (2CH) was deleted using BROWSE, playback of that track would become not possible. This has been fixed. - After flash loading an MP3 track that was about one second long, playback would not be possible and a "Play Error." message would appear. This has been fixed. - If RENAME was executed using BROWSE, the track playback order would change. This has been fixed. - When recording with MONO (MIX), files would not be uploaded even when AUTO UPLOAD was ON. This has been fixed. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.10 ----------------------------------------------------------------------------------------- < New functions > - TASCAM SS250 CONTROL (Ver1.1.0) is now supported. - A TIME mode has been added to the AUTO TRACK function. Setting options: 1min-10min, 15min, 30min, 1hour, 2hour, 6hour, 8hour, 12hour, 24hour (default: 5min) [ Confirm the following items before using a TASCAM SS250 CONTROL ] To use a TASCAM SS250 CONTROL, confirm that its firmware version is Ver1.1.0 or higher. If the version is older than Ver1.1.0, update it to Ver1.1.0 or higher. For information about how to install the application, visit the TASCAM Web site ( https://tascam.jp/int/product/ss250_control/support ). < Maintenance items > - After the FLASH LOAD function was executed, if tracks were played back consecutively, noise would occur on rare occasions. This has been fixed. - When the recording format setting was MP3 and 64kbps was selected, recording would freeze. This has been fixed. - When the recording format setting was MP3, noise would occur at the end of recording. This has been fixed. - Mark setting operation has been improved. - Media recognition has been improved. - USB keyboard recognition has been improved. - Operation stability has been improved. ----------------------------------------------------------------------------------------- Unit firmware: V1.01 ----------------------------------------------------------------------------------------- < New functions > - TASCAM SS250 CONTROL is now supported. - RC-900 is now supported. [ Confirm the following items before using the RC-900 ] To use an RC-900, confirm that its firmware version is Ver1.30 or higher. If the version is older than Ver1.30, update it to Ver1.30 or higher. For instructions about updating firmware, visit the TASCAM Web Site. ( https://tascam.jp/int/product/rc-900/support ) < Maintenance items > - When an MP3 file was played, the mark display for the first track would disappear. This has been fixed. - MP3 file flash playback operation has been improved. - Operation stability has been improved.